| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: tlb: Flush walk cache when unsharing PMD tables
When huge_pmd_unshare() is called to unshare a PMD table, the
tlb_unshare_pmd_ptdesc() function sets tlb->unshared_tables=true
but the aarch64 tlb_flush() only checked tlb->freed_tables to
determine whether to use TLBF_NONE (vae1is, invalidates walk
cache) or TLBF_NOWALKCACHE (vale1is, leaf-only).
This caused the stale PMD page table entry to remain in the walk cache
after unshare, potentially leading to incorrect page table walks.
Fix by including unshared_tables in the check, so that when
unsharing tables, TLBF_NONE is used and the walk cache is properly
invalidated.
Here is the detailed distinction between vae1is and vale1is:
| Instruction Combination | Actual Invalidation Scope |
| ------------------------ | --------------------------------------------------|
| `VAE1IS` + TTL=`0` | All entries at all levels (full invalidation) |
| `VAE1IS` + TTL=`2` (L2) | Non-leaf at Level 0/1 + leaf at Level 2 |
| `VALE1IS` + TTL=`0` | Leaf entries at all levels (non-leaf not cleared) |
| `VALE1IS` + TTL=`2` (L2) | Leaf entry at Level 2 only | |
| In the Linux kernel, the following vulnerability has been resolved:
Drivers: hv: Don't reset VMBus connection state on error/exit paths
In two places, current code forces vmbus_connection.conn_state to
DISCONNECTED prior to calling vmbus_disconnect(). But vmbus_disconnect()
calls vmbus_initiate_unload(), which unloads the VMBus connection
only if the conn_state is CONNECTED. Consequently, the connection
remains and the Hyper-V host might continue to send messages or post
VMBus interrupts.
The problem was introduced in commit 74347a99e73ae ("x86/Hyper-V:
Unload vmbus channel in hv panic callback"), in that
vmbus_initiate_unload() started checking the current connection
state before doing the unload. This commit removed some occurrences
where conn_state was forced to DISCONNECTED, but these two remained,
apparently due to an oversight at the time.
Fix this by not forcing conn_state to DISCONNECTED during VMBus exit,
or if a failure occurs when establishing the connection in the first
place. Whatever value conn_state has at the time is then read by
vmbus_initiate_unload() to determine if there is a connection to
be unloaded. |
| In the Linux kernel, the following vulnerability has been resolved:
ibmveth: h_free logical LAN on open-fail after register
ibmveth_open() registers the logical LAN, then allocates the RX
buffer pools. A pool failure jumps to out_free_buffer_pools without
h_free_logical_lan(), so PHYP still owns the buffer-list page when
it is unmapped. request_irq() failure already issued the hypercall
before taking the same label.
Move that h_free to the shared post-register unwind so both paths
deregister before the buffer list is unmapped. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: sdhci-sprd: disable runtime PM on remove
sdhci_sprd_probe() enables runtime PM, while sdhci_sprd_remove() does
not perform the corresponding runtime PM cleanup.
The probe failure path disables runtime PM before disabling the clocks,
but the normal remove path directly disables clocks that are also
managed by the runtime PM callbacks. If the device is runtime
suspended, those clocks may already be disabled.
Resume the device before removal, disable runtime PM and drop the
temporary runtime PM reference before disabling the clocks.
This issue was found by manual code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: steam: Refactor registration
This refactors and simplifies the registration/unregistration flow. Since
we now only perform registration when the client isn't opened anymore, the
logic for handling that can be removed, and the rest of the function
streamlined.
We also remove the previous assumption that we have a serial number to show
we're registered, replacing it with a single purpose boolean.
In a previous refactor the code for unregistering a battery if later
registration steps failed was accidentally left out. As a result, a
lingering power_supply object could get left over after the steam object
was torn down. This is also fixed here. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/server: fix session leak in ksmbd_session_register()
See the procedure below:
smb2_sess_setup
ksmbd_smb2_session_create
__session_create
atomic_set(&sess->refcnt, 2)
hash_add(sessions_table, &sess->hlist, sess->id)
ksmbd_session_register
xa_store(&conn->sessions, sess->id, sess) // fail
ksmbd_user_session_put
atomic_dec(&sess->refcnt) // refcnt is 1, session is not freed
Remove the session from sessions_table and drop its table reference if
xa_store() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix dentry folio leak in find_in_level
find_in_level() gets a dentry folio with f2fs_find_data_folio() before
calling find_in_block(). If find_in_block() returns an error, the
function stores the error in res_folio and breaks out of the loop without
dropping the dentry folio.
This leaks the folio reference on the find_in_block() error path. Drop
the dentry folio before returning the error to the caller. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Allow per function PCI slots to fix slot reset on s390
On s390 systems, which use a machine level hypervisor, PCI devices are
always accessed through a form of PCI pass-through which fundamentally
operates on a per PCI function granularity. This is also reflected in the
s390 PCI hotplug driver which creates hotplug slots for individual PCI
functions. Its reset_slot() function, which is a wrapper for
zpci_hot_reset_device(), thus also resets individual functions.
Currently, the pci_create_slot() assigns the same pci_slot object to
multifunction devices. This approach worked fine on s390 systems that only
exposed virtual functions as individual PCI domains to the operating
system. Since commit 44510d6fa0c0 ("s390/pci: Handling multifunctions")
s390 supports exposing the topology of multifunction PCI devices by
grouping them in a shared PCI domain. This creates a problem when resetting
a function through the hotplug driver's slot_reset() interface.
When attempting to reset a function through the hotplug driver, the shared
slot assignment causes the wrong function to be reset instead of the
intended one. It also leaks memory as we do create a pci_slot object for
the function, but don't correctly free it in pci_slot_release().
Add a flag for struct pci_slot to allow per function PCI slots for
functions managed through a hypervisor, which exposes individual PCI
functions while retaining the topology. Since we can use all 8 bits for
slot 'number' (for ARI devices), change slot 'number' u16 to account for
special values PCI_SLOT_PLACEHOLDER and PCI_SLOT_ALL_DEVICES. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpci_rt1711h: unregister TCPCI port with devres
rt1711h_probe() registers the TCPCI port before requesting the interrupt
and enabling alert interrupts. If either of those later steps fails, the
probe function returns without unregistering the TCPCI port. The explicit
unregister currently only happens from the remove callback.
Register a devres action immediately after tcpci_register_port() succeeds,
so tcpci_unregister_port() runs on later probe failures and on driver
detach. Drop the remove callback to avoid unregistering the same port
twice.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
test_kprobes: clear kprobes between test runs
Running the kprobes sanity tests twice makes all tests fail and
eventually crashes the kernel.
[root@martin-riscv-1 ~]# echo 1 > /sys/kernel/debug/kunit/kprobes_test/run
...
# Totals: pass:5 fail:0 skip:0 total:5
ok 1 kprobes_test
[root@martin-riscv-1 ~]# echo 1 > /sys/kernel/debug/kunit/kprobes_test/run
...
# test_kprobe: EXPECTATION FAILED at lib/tests/test_kprobes.c:64
Expected 0 == register_kprobe(&kp), but
register_kprobe(&kp) == -22 (0xffffffffffffffea)
...
Unable to handle kernel paging request ...
The testsuite defines several kprobes and kretprobes as static variables
that are preserved across test runs.
After register_kprobe and unregister_kprobe, a kprobe contains some
leftover data that must be cleared before the kprobe can be registered
again. The tests are setting symbol_name to define the probe location.
Address and flags must be cleared.
The existing code clears some of the probes between subsequent tests, but
not between two test runs. The leftover data from a previous test run
makes the registrations fail in the next run.
Move the cleanups for all kprobes into kprobes_test_init, this function
is called before each single test (including the first test of a test
run). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: only release the dirty pages io tree after successful writes
[WARNING]
With extra warning on dirty extent buffers at umount (aka, the next
patch in the series), test case generic/388 can trigger the following
warning about dirty extent buffers at unmount time:
BTRFS critical (device dm-2 state E): emergency shutdown
BTRFS error (device dm-2 state E): error while writing out transaction: -30
BTRFS warning (device dm-2 state E): Skipping commit of aborted transaction.
BTRFS error (device dm-2 state EA): Transaction 9 aborted (error -30)
BTRFS: error (device dm-2 state EA) in cleanup_transaction:2068: errno=-30 Readonly filesystem
BTRFS info (device dm-2 state EA): forced readonly
BTRFS info (device dm-2 state EA): last unmount of filesystem 4fbf2e15-f941-49a0-bc7c-716315d2777c
------------[ cut here ]------------
WARNING: disk-io.c:3311 at invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs], CPU#8: umount/914368
CPU: 8 UID: 0 PID: 914368 Comm: umount Tainted: G OE 7.1.0-rc1-custom+ #372 PREEMPT(full) 2de38db8d1deae71fde295430a0ff3ab98ccf596
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022
RIP: 0010:invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs]
Call Trace:
<TASK>
close_ctree+0x52e/0x574 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
generic_shutdown_super+0x89/0x1a0
kill_anon_super+0x16/0x40
btrfs_kill_super+0x16/0x20 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
deactivate_locked_super+0x2d/0xb0
cleanup_mnt+0xdc/0x140
task_work_run+0x5a/0xa0
exit_to_user_mode_loop+0x123/0x4b0
do_syscall_64+0x243/0x7c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30539776 owner 9 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30621696 owner 257 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30638080 owner 258 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30654464 owner 7 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30703616 owner 2 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30720000 owner 10 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30736384 owner 4 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30752768 owner 11 gen 9 refs 2 flags 0x7
I'm using a stripped down version, which seems to trigger the warning
more reliably:
_fsstress_pid=""
workload()
{
dmesg -C
mkfs.btrfs -f -K $dev > /dev/null
echo 1 > /sys/kernel/debug/clear_warn_once
mount $dev $mnt
$fsstress -w -n 1024 -p 4 -d $mnt &
_fsstress_pid=$!
sleep 0
$godown $mnt
pkill --echo -PIPE fsstress > /dev/null
wait $_fsstress_pid
unset _fsstress_pid
umount $mnt
if dmesg | grep -q "WARNING"; then
fail
fi
}
for (( i = 0; i < $runtime; i++ )); do
echo "=== $i/$runtime ==="
workload
done
[CAUSE]
Inside btrfs_write_and_wait_transaction(), we first try to write all
dirty ebs, then wait for them to finish.
After that we call btrfs_extent_io_tree_release() to free all
extent states from dirty_pages io tree.
However if we hit an error from btrfs_write_marked_extent(), then we
still call btrfs_extent_io_tree_release() to clear that dirty_pages io
tree, which may contain dirty records that we haven't yet submitted.
Furthermore, the later transaction cleanup path will utilize that
dirty_pages io tree to properly cleanup those dirty ebs, but since it's
already empty, no dirty ebs are properly cleaned up, thus will later
trigger the warnings inside invalidate_btree_folios().
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: clean the sfp upstream if phy probing fails
Sashiko reported that we don't call sfp_bus_del_upstream() in the probe
failure path, so let's add it, otherwise the sfp-bus is left with a
dangling 'upstream' field, that may be used later on during SFP events.
This issue existed before the generic phylib sfp support, back when
drivers were calling phy_sfp_probe themselves. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: mpc52xx: fix controller deregistration
Make sure to deregister the controller before disabling and releasing
underlying resources like interrupts and gpios during driver unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: drop extent cache when splitting extent fails
When the split extent fails, we might leave some extents still being
processed and return an error directly, which will result in stale
extent entries remaining in the extent status tree. So drop all of the
remaining potentially stale extents if the splitting fails. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: chipidea: udc: fix DMA and SG cleanup in _ep_nuke()
The ChipIdea UDC driver can encounter "not page aligned sg buffer"
errors when a USB device is reconnected after being disconnected
during an active transfer. This occurs because _ep_nuke() returns
requests to the gadget layer without properly unmapping DMA buffers
or cleaning up scatter-gather bounce buffers.
Root cause:
When a disconnect happens during a multi-segment DMA transfer, the
request's num_mapped_sgs field and sgt.sgl pointer remain set with
stale values. The request is returned to the gadget driver with status
-ESHUTDOWN but still has active DMA state. If the gadget driver reuses
this request on reconnect without reinitializing it, the stale DMA
state causes _hardware_enqueue() to skip DMA mapping (seeing non-zero
num_mapped_sgs) and attempt to use freed/invalid DMA addresses,
leading to alignment errors and potential memory corruption.
The normal completion path via _hardware_dequeue() properly calls
usb_gadget_unmap_request_by_dev() and sglist_do_debounce() before
returning the request. The _ep_nuke() path must do the same cleanup
to ensure requests are returned in a clean, reusable state.
Fix:
Add DMA unmapping and bounce buffer cleanup to _ep_nuke() to mirror
the cleanup sequence in _hardware_dequeue():
- Call usb_gadget_unmap_request_by_dev() if num_mapped_sgs is set
- Call sglist_do_debounce() with copy=false if bounce buffer exists
This ensures that when requests are returned due to endpoint shutdown,
they don't retain stale DMA mappings. The 'false' parameter to
sglist_do_debounce() prevents copying data back (appropriate for
shutdown path where transfer was aborted). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_eem: Fix net_device lifecycle with device_move
The net_device is allocated during function instance creation and
registered during the bind phase with the gadget device as its sysfs
parent. When the function unbinds, the parent device is destroyed, but
the net_device survives, resulting in dangling sysfs symlinks:
console:/ # ls -l /sys/class/net/usb0
lrwxrwxrwx ... /sys/class/net/usb0 ->
/sys/devices/platform/.../gadget.0/net/usb0
console:/ # ls -l /sys/devices/platform/.../gadget.0/net/usb0
ls: .../gadget.0/net/usb0: No such file or directory
Use device_move() to reparent the net_device between the gadget device
tree and /sys/devices/virtual across bind and unbind cycles. During the
final unbind, calling device_move(NULL) moves the net_device to the
virtual device tree before the gadget device is destroyed. On rebinding,
device_move() reparents the device back under the new gadget, ensuring
proper sysfs topology and power management ordering.
To maintain compatibility with legacy composite drivers (e.g., multi.c),
the bound flag is used to indicate whether the network device is shared
and pre-registered during the legacy driver's bind phase. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: always walk all pending catchall elements
During transaction processing we might have more than one catchall element:
1 live catchall element and 1 pending element that is coming as part of the
new batch.
If the map holding the catchall elements is also going away, its
required to toggle all catchall elements and not just the first viable
candidate.
Otherwise, we get:
WARNING: ./include/net/netfilter/nf_tables.h:1281 at nft_data_release+0xb7/0xe0 [nf_tables], CPU#2: nft/1404
RIP: 0010:nft_data_release+0xb7/0xe0 [nf_tables]
[..]
__nft_set_elem_destroy+0x106/0x380 [nf_tables]
nf_tables_abort_release+0x348/0x8d0 [nf_tables]
nf_tables_abort+0xcf2/0x3ac0 [nf_tables]
nfnetlink_rcv_batch+0x9c9/0x20e0 [..] |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do proper folio cleanup when cow_file_range() failed
[BUG]
When testing with COW fixup marked as BUG_ON() (this is involved with the
new pin_user_pages*() change, which should not result new out-of-band
dirty pages), I hit a crash triggered by the BUG_ON() from hitting COW
fixup path.
This BUG_ON() happens just after a failed btrfs_run_delalloc_range():
BTRFS error (device dm-2): failed to run delalloc range, root 348 ino 405 folio 65536 submit_bitmap 6-15 start 90112 len 106496: -28
------------[ cut here ]------------
kernel BUG at fs/btrfs/extent_io.c:1444!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
CPU: 0 UID: 0 PID: 434621 Comm: kworker/u24:8 Tainted: G OE 6.12.0-rc7-custom+ #86
Hardware name: QEMU KVM Virtual Machine, BIOS unknown 2/2/2022
Workqueue: events_unbound btrfs_async_reclaim_data_space [btrfs]
pc : extent_writepage_io+0x2d4/0x308 [btrfs]
lr : extent_writepage_io+0x2d4/0x308 [btrfs]
Call trace:
extent_writepage_io+0x2d4/0x308 [btrfs]
extent_writepage+0x218/0x330 [btrfs]
extent_write_cache_pages+0x1d4/0x4b0 [btrfs]
btrfs_writepages+0x94/0x150 [btrfs]
do_writepages+0x74/0x190
filemap_fdatawrite_wbc+0x88/0xc8
start_delalloc_inodes+0x180/0x3b0 [btrfs]
btrfs_start_delalloc_roots+0x174/0x280 [btrfs]
shrink_delalloc+0x114/0x280 [btrfs]
flush_space+0x250/0x2f8 [btrfs]
btrfs_async_reclaim_data_space+0x180/0x228 [btrfs]
process_one_work+0x164/0x408
worker_thread+0x25c/0x388
kthread+0x100/0x118
ret_from_fork+0x10/0x20
Code: aa1403e1 9402f3ef aa1403e0 9402f36f (d4210000)
---[ end trace 0000000000000000 ]---
[CAUSE]
That failure is mostly from cow_file_range(), where we can hit -ENOSPC.
Although the -ENOSPC is already a bug related to our space reservation
code, let's just focus on the error handling.
For example, we have the following dirty range [0, 64K) of an inode,
with 4K sector size and 4K page size:
0 16K 32K 48K 64K
|///////////////////////////////////////|
|#######################################|
Where |///| means page are still dirty, and |###| means the extent io
tree has EXTENT_DELALLOC flag.
- Enter extent_writepage() for page 0
- Enter btrfs_run_delalloc_range() for range [0, 64K)
- Enter cow_file_range() for range [0, 64K)
- Function btrfs_reserve_extent() only reserved one 16K extent
So we created extent map and ordered extent for range [0, 16K)
0 16K 32K 48K 64K
|////////|//////////////////////////////|
|<- OE ->|##############################|
And range [0, 16K) has its delalloc flag cleared.
But since we haven't yet submit any bio, involved 4 pages are still
dirty.
- Function btrfs_reserve_extent() returns with -ENOSPC
Now we have to run error cleanup, which will clear all
EXTENT_DELALLOC* flags and clear the dirty flags for the remaining
ranges:
0 16K 32K 48K 64K
|////////| |
| | |
Note that range [0, 16K) still has its pages dirty.
- Some time later, writeback is triggered again for the range [0, 16K)
since the page range still has dirty flags.
- btrfs_run_delalloc_range() will do nothing because there is no
EXTENT_DELALLOC flag.
- extent_writepage_io() finds page 0 has no ordered flag
Which falls into the COW fixup path, triggering the BUG_ON().
Unfortunately this error handling bug dates back to the introduction of
btrfs. Thankfully with the abuse of COW fixup, at least it won't crash
the kernel.
[FIX]
Instead of immediately unlocking the extent and folios, we keep the extent
and folios locked until either erroring out or the whole delalloc range
finished.
When the whole delalloc range finished without error, we just unlock the
whole range with PAGE_SET_ORDERED (and PAGE_UNLOCK for !keep_locked
cases)
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
s390/pkey: Wipe copies of clear-key structures on failure
Wipe all sensitive data from stack for all IOCTLs, which convert a
clear-key into a protected- or secure-key. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/pkey: Wipe copies of protected- and secure-keys
Although the clear-key of neither protected- nor secure-keys is
accessible, this key material should only be visible to the calling
process. So wipe all copies of protected- or secure-keys from stack,
even in case of an error. |
